Clay-paky ALPHA SPOT HPE 700 Manuel d'utilisateur télécharger pdf (Page 2)

ALPHA SPOT HPE 700

700W

150°C

Risk Group 2

According to

EN 62471

• Installation

Make sure all parts for fixing the projector are in a good state of repair.

Make sure the point of anchorage is stable before positioning the projector.

The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary

support system fails, the fitting falls as little as possible.

If the safety chain gets used, it needs to be replaced with a genuine spare.

• Minimum distance of illuminated objects

The projector needs to be positioned so that the objects hit by the beam of light are at least 3 metres (9'10'') from

the lens of the projector.

• Minimum distance from flammable materials

The projector must be positioned so that any flammable materials are at least 0.20 metres (8”) from every point on

the surface of the fitting.

• Maximum ambient temperature

Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

• IP20 protection rating

The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first digit 2), but not

against dripping water, rain, splashes or jets of water (second digit 0).

• Protection against electrical shock

Connection must be made to a power supply system fitted with efficient earthing (Class I appliance according to

standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the projectors from indirect

contact and/or shorting to earth by using appropriately sized residual current devices.

• Connection to mains supply

Connection to the electricity mains must be carried out by a qualified electrical installer.

Check that the mains frequency and voltage correspond to those for which the projector is designed as given on the

electrical data label.

This label also gives the input power to which you need to refer to evaluate the maximum number of fittings to

connect to the electricity line, in order to avoid overloading.

IMPORTANT: to prevent EMI disturbances, in some condition it might be necessary to clip around the DMX and the

Ethernet cable, as close as possible to the projector, an appropriate ferrite bead. Shielded cables must always be used.

• Temperature of the external surface

The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is

150°C (302°F).

• Maintenance

Before starting any maintenance work or cleaning the projector, cut off power from the mains supply.

After switching off, do not remove any parts of the fitting for at least 10 minutes. After this time the likelihood of the

lamp exploding is virtually nill. If it is necessary to replace the lamp, wait for another 20 minutes to avoid getting

burnt.

The fitting is designed to hold in any splinters produced by a lamp exploding. The lenses must be mounted and, if

visibly damaged, they have to be replaced with genuine spares.

• Lamp

The fitting mounts a high-pressure lamp that needs an external igniter. This igniter is fitted onto the apparatus.

- Carefully read the "operating instructions" provided by the lamp manufacturer.

- Immediately replace the lamp if damaged or deformed by heat.

• Photobiological Safety

CAUTION. Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be

harmful to the eyes. The fixture must be positioned so that the minimum distance between the front lens and human

eye is at least 1 metre to prevent personal photobiological risks.

This product is intended for the following areas of application:

studios, stages, theaters, exhibitions, trade fairs, events, theme parks, entertainment venues, architectural lighting

and similar.

SAFETY INFORMATION

IP20

40°C

1 2 3 4 5 6 7 ... 39 40

Commentaires sur ces manuels

Pas de commentaire

Clay-paky ALPHA SPOT HPE 700 Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Projecteurs Clay-paky ALPHA SPOT HPE 700