INSTRUCTIONS MANUAL
Carefully read this instructions manual in its entirety and keep it safe for future
reference.
It is essential to know the information and comply with the instructions given
in this manual in order to ensure the fitting is installed, used and serviced cor-
rectly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other
property or persons deriving from installation, use and maintenance that have
not been carried out in conformity with this instructions manual, which must
always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the characteristics stated in
this instructions manual at any time and without prior notice.
Congratulations on choosing a Clay Paky product! We thank you for your cu-
stom. Please note that this product, as all the others in the rich Clay Paky
range, has been designed and made with total quality to ensure excellent
performance and best meet your expectations and requirements.
•
Installation
Make sure all the parts for fixing the smoke machine are in a good state of repair.
Make sure the point of anchorage is stable before positioning the fitting.
•
Minimum distance of flammable materials
The fitting must be positioned so that any flammable materials are at least 1 metre
(3’ 3”) from every point on the surface of the fitting.
•
Direction and distance of the jet of smoke
Never turn the jet of smoke onto people or items that are flammable or can get
damaged or dirtied by the jet of smoke.
Installation above people is not permitted.
•
Maximum ambient temperature
For the fitting to operate well and reliably, the ambient temperature should not
exceed 35°C (95°F).
•
IP20 protection rating
The fitting is protected against penetration by solid bodies with a diameter of over
12mm (0,47”) (first digit 2), but not against dripping water, rain, splashes or jets of
water (second digit 0).
•
Protection against electrical shock
This fitting is classified, in accordance with the type of protection against electrical
shock, in Class I. It must therefore be connected to a power supply system with
efficient earthing.
It is, moreover, recommended to protect the supply lines of the projectors from in-
direct contact and/or shorting to earth by using appropriately sized residual cur-
rent devices.
•
Hooking up to the supply mains
The operations for connecting to the electricity mains must be carried out by a
qualified electrical installer.
Check that the mains frequency and voltage correspond to the frequency and vol-
tage for which the smoke machine is designed, given on the rear panel.
This panel also gives the input power. Refer to this to evaluate the maximum num-
ber of fittings to connect to the electricity line in order to avoid overloading.
•
Maintenance
Before starting any maintenance work or cleaning the fitting, cut off power from
the supply mains.
After switching off, do not touch the smoke nozzle for at least 1 hour to avoid
getting burnt.
•
Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fit-
ting, in a thermally steady state, is 60°C (140°F) except for on the smoke nozzle
where it reaches 300°C (572°F).
The products referred to in this manual conform to the Eu-
ropean Community Directives to which they are subject:
• Low Voltage 73/23
• Electromagnetic Compatibility 89/336
SAFETY INFORMATION
1
UNPACKING AND PREPARATION
2
• Packing contents
Besides the smoke machine, the
packing also contains the following
accessories:
- Remote control (1) code
177034/801 (for GOLDEN FOG
1000 and 2000 models only).
- Socket for mounting on cable co-
de 030210 (2).
- 2 screws (3) code 020002/029 (mo-
dels 2000 and 2000 DMX only).
- 4 toothed washers (4) code
020201/005 (models 2000 and
2000 DMX only).
- This instructions manual code
099595 (5).
1
5
2
3
4
•
Projector mounting
GOLDEN FOG 1000
Position the bracket (6) according to the desired angle and lock it with the knobs
(7). The bracket (6) can be height adjusted by using the two holes on the bracket; it
can moreover also be mounted towards the bottom of the fitting. These last steps
require fully extracting the knobs (7), putting the bracket (6) back into the desired
position and reinserting the knobs (7), tightening them appropriately.
6
7
ENGLISH
(4 pages)
(4 pages)
(4 pages)
(7 pages)
(7 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels