Clay-paky ALPHA WASH 700 (C61350) Manuel d'utilisateur

1ALPHA WASH 700C61350®INSTRUCTION MANUALCongratulations on choosing a Clay Paky product! We thank you for your custom. Please note that this product,

10ALPHA WASH 700Save ToPreset 3SHUTTERShutter on errorUsed for automatically closing the stop/strobe in the event of Pan/Tiltposition error.

11ALPHA WASH 700Continue ➔SYSTEM ERRORSShows a list of warnings and messages relevant to errors occurred sincethe fixtures switching-on.1) Pressing F

12ALPHA WASH 7002) Press Fto reset partial lamp strikes hours, a confirmation message(Are you sure ?) appears on the display.3) Select YES to reset pa

13ALPHA WASH 700To enable the "Advanced Menu" set up the "Access code" (1234) using theUP B, DOWN C, RIGHT Ekeys.PressF- "Men

14ALPHA WASH 700Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section.Opening the head cov

2Lower SideAUpper Side1A3A15ALPHA WASH 700Upper SideLower Side13141212Lamp change - Fig 13Take the new lamp out of its package and insert in the fit

16ALPHA WASH 700Periodical cleaning- Fig. 15To ensure optimal operation and performance for a long time it is essential to periodically clean the part

17ALPHA WASH 7002341ThermostatLower SideUpper Side16Extraction of the effect modules: Preliminary operations - Fig. 16099100_AlphaWash700_Rv2_EN_ 23/

18ALPHA WASH 700Extraction of the effect modules - Fig. 17IMPORTANT: Grasp the modules using the support structure and not the details which could get

19ALPHA WASH 700Extraction of the effect modules - Fig. 18IMPORTANT: Grasp the modules using the support structure and not the details which could get

2ALPHA WASH 700• InstallationMake sure all parts for fixing the projector are in a good state of repair.Make sure the point of anchorage is stable bef

20ALPHA WASH 700Extraction of the effect modules - Fig. 19IMPORTANT: Grasp the modules using the support structure and not the details which could get

21ALPHA WASH 70050(1,97")220(8,66")405(15.94")385(15,16")390(15,35")220(8,66")575(22.64")375(14.76")505(19,88&

22ALPHA WASH 700ALPHA WASH 700CHANNEL FUNCTIONCHANNELSTANDARD VECTORCHANNEL MODECYAN MAGENTA YELLOW CTOCOLOUR WHEELSTOP / STROBEDIMMERDIMMER FINEBEAM

23ALPHA WASH 700BIT % EFFECT255 100COLOUR EXCLUDED0 0.0COLOUR INSERTEDCHANNEL 1CYANCHANNEL 2MAGENTACHANNEL 3YELLOWBIT% EFFECT255 100COLOUR INSERTED0 0

24ALPHA WASH 700• BEAM SHAPER ROTATION - channel 10STOPFAST ROTATION (120 rpm)SLOW ROTATION (3 rph)SLOW ROTATION (3 rph)FAST ROTATION (120 rpm)BIT % E

25ALPHA WASH 700•LAMP CONTROL (only with option LAMP DMX On) - channel: 18IMPORTANT: Alpha Wash 700 is not provided with hot restrike igniterLAMP ON (

26ALPHA WASH 700Timing Channel Channel function 19 Pan - Tilt time

099100_AlphaWash700_Rv2_EN_ 23/02/11 17.06 Pagina 27

CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035 -654311 - Fax +39-035-301876 - www.claypaky.itRev.2 02/11 Cod. 099100

UNLOCKEDLOCKED45°45°45°45°45°45°45°45°45°45°45°45°3ALPHA WASH 700UNPACKING AND PREPARATIONLamp 700W(fitted into projector)0991002 x 183102/802190°90°9

4ALPHA WASH 7004123215INSTALLATION AND START-UPConnecting and disconnecting power cable - Fig. 5Installing the projector - Fig. 4The projector can be

5ALPHA WASH 700Switching on the projector - Fig. 8Press the switch. The projector starts resetting the effects. At the same time, the following inform

6ALPHA WASH 7002828Reversal of the display - Fig. 9To activate this function, press UPBand DOWNCkeys simultaneously while the display is in the rest

7ALPHA WASH 700System ErrorsInformationFixture HoursLampHours4LampManualControlResetChannel6MAIN MENUMENU SETTING3LampStrikesSystem VersionBoardDiagno

8ALPHA WASH 700DMX ADDRESSNOTE: without the DMX signal the Address (XXX) flashingAllows you to select the DMX ADDRESS.1) Press F- the current DMX Adre

9ALPHA WASH 700Continue ➔ LAMP DMXUsed for enabling lamp remote control channel.1) Press F- the current settings appear on the display (On or Off).2